TECHNICAL models from the demineralizer family equipped with various modules and filters.List of all elements together with catalog numbers included below in the tabs.
The table with individual components of content is in PDF.
Cat. no.: EO-005-10
The sludge insert prepares tap water for the purification process in the Technical Plus demineralizers. They are made of polypropylene fiber wound on a filter core, thus creating a gradient filter. They retain mechanical impurities with a particle size of 1µm to 20µm (depending on the porosity of the filter). The life of the cartridges is 3-6 months (it may change depending on the flow and the level and type of water pollution).
Cat. no: EW-001-10
Coal cartridges prepare tap water for further purification by removing chlorine and chlorine derivatives dissolved in tap water. Impurities are sorbed on activated carbon. The module’s service life is 3-6 months (it may change depending on the flow and the level and type of water pollution).
Cat. no: EO-001-L
The mechanical filter prepares tap water for further purification in demineralisers manufactured until the end of April 2013. It is made of a 1 µm polypropylene cartridge placed in the filter housing (¼” NPT connection). The module’s service life is 3-6 months (it may change depending on the flow and the level and type of water pollution).
Cat. no. EW-001-L
The carbon filter prepares tap water for further purification in demineralisers produced until the end of April 2013. The filter is filled with granular activated carbon located in the filter housing (¼ ”NPT connection). Impurities (mainly chlorine and chlorinated substances dissolved in tap water) are sorbed on activated carbon. The module’s service life is 3-6 months (it may change depending on the flow and the level and type of water pollution).
Cat. no: EO-MA-12
The sediment-carbon-softening module prepares tap water for the reverse osmosis process in the HLP, Technical, Technical Plus, Spring and R series demineralizers. Removes mechanical particles (sand, rust, mud), chlorine, chlorinated substances dissolved in water and calcium and magnesium ions responsible for water hardness. The module’s service life is 3-6 months (it may change depending on the flow and the level and type of water pollution).
Cat. no: EUV-254-HLP – from April 2013 r
Cat. no: EUV-254-0 – to April 2013 r
The radiator emits radiation at a wavelength of 254 nm, which causes a photochemical reaction that damages the DNA structures of microorganisms in the water. This type of radiator is used in models HLP 5-30UV, R 5-60, Ultra, Spring 5-60UV. Its proper operation is up to 8,500 hours.Warning! In models until April 2013, we used the EUV-254-0 radiator type.
TECHNICAL PLUS models from the demineralizer family equipped with various modules and filters.List of all elements together with catalog numbers included below in the tabs.
The table with individual components of content is in PDF.
Cat.no: EO-005-10
The sediment prefilter prepares tap water for the purification process in the Technical Plus demineralizers. They are made of polypropylene fiber wound on a filter core, thus creating a gradient filter. They retain mechanical impurities with a particle size of 1µm to 20µm (depending on the porosity of the filter). The life of the cartridges is 3-6 months (it may change depending on the flow and the level and type of water pollution).
Cat. no: EW-001-10
Coal cartridges prepare tap water for further purification by removing chlorine and chlorine derivatives dissolved in tap water. Impurities are sorbed on activated carbon. The module’s service life is 3-6 months (it may change depending on the flow and the level and type of water pollution).We use GAC 10 “only on Technical Plus 40 and Technical Plus 60 models.
Cat. no.: EO-MA-12
The sediment-carbon-softening module prepares tap water for the reverse osmosis process in the HLP, Technical, Technical Plus, Spring and R series demineralizers. Removes mechanical particles (sand, rust, mud), chlorine, chlorinated substances dissolved in water and calcium and magnesium ions responsible for water hardness. The module’s service life is 3-6 months (it may change depending on the flow and the level and type of water pollution).
Cat. no: EJ-5000-0
The H6 ion exchange module is a mixture of ion exchange beds – strongly acid cation exchanger and strongly basic anion exchanger. Removes mineral salts remaining in water after reverse osmosis to less than 0.06 µS/cm. In this model one H6 column should be replaced. It should be remembered that the volume of purified water depends on the quality of the feed water, the maximum amount of salts dissolved in the feed water – 1200 mg / l. After 5000 dm3, the H6 module should be replaced.
Cat. no.: EJ-2000-0
The H7 ion exchange module is a mixture of ion exchange beds – strongly acid cation exchanger and strongly basic anion exchanger. Removes mineral salts remaining in water after reverse osmosis to less than 0.06 µS / cm. In this model, the 2xH7 set should be replaced. In demineralizers manufactured until the end of April 2013, it appears as a “cleaning filter”.
Cat. no.: EUV-254-HLP
The radiator emits radiation at a wavelength of 254 nm, which causes a photochemical reaction that damages the DNA structures of microorganisms in the water. We use the heater in Technical Plus models as an option. Its proper operation is up to 8,500 hours.
HLP (HLP5, HLP 10, HLP 20, HLP 30, HL Smart) models from the demineralizer family equipped with various modules and filters.List of all elements together with catalog numbers included below in the tabs.
The table with individual components of content is in PDF.
Cat.no: EO-005-10
The sediment prefilter prepares tap water for the purification process in the Technical Plus demineralizers. They are made of polypropylene fiber wound on a filter core, thus creating a gradient filter. They retain mechanical impurities with a particle size of 1µm to 20µm (depending on the porosity of the filter). The life of the cartridges is 3-6 months (it may change depending on the flow and the level and type of water pollution).
Cat. no.: EO-001-L
The mechanical filter prepares tap water for further purification in demineralisers manufactured until the end of April 2013. It is made of a 1 µm polypropylene cartridge placed in the filter housing (1/4″ NPT connection). The module’s service life is 3-6 months (it may change depending on the flow and the level and type of water pollution).
Cat. no: EW-001-L
The carbon filter prepares tap water for the further purification process in demineralisers manufactured until the end of April 2013. The filter is filled with granular activated carbon located in the filter housing (¼ ”NPT connection). Impurities (mainly chlorine and chlorinated substances dissolved in tap water) undergo sorption on activated carbon. The lifetime of the module is 3-6 months (it may change depending on the flow and the level and type of water pollution).
Cat. no.: EO-MA-12
The sediment-carbon-softening module prepares tap water for the reverse osmosis process in the HLP, Technical, Technical Plus, Spring and R series demineralizers. Removes mechanical particles (sand, rust, mud), chlorine, chlorinated substances dissolved in water and calcium and magnesium ions responsible for water hardness. The module’s service life is 3-6 months (it may change depending on the flow and the level and type of water pollution).
Cat. no.: EJ-0500-0
The H3 ion exchange filter is a mixture of ion-exchange beds – strongly acid cation exchanger and strongly basic anion exchanger (500 ml bed). Removes mineral salts remaining in water after reverse osmosis to less than 0.06 µS/cm. It occurs in demineralizers manufactured until the end of April 2013 as a cleaning filter. The working capacity of the H3 filter is 28g CaCO3/dm3
Cat. no: EJ-0250-0
The H5 ion exchange filter is a mixture of ion exchange beds – strongly acid cation exchanger and strongly basic anion exchanger (250 ml bed). Removes mineral salts remaining in water after reverse osmosis to less than 0.06 µS/cm. It occurs in demineralizers manufactured until the end of April 2013 as a cleaning filter. The working capacity of the H5 filter is 28g CaCO3/dm3
Cat. no.: EJ-5000-0
The H6 ion exchange module is a mixture of ion exchange beds – strongly acid cation exchanger and strongly basic anion exchanger. Removes mineral salts remaining in water after reverse osmosis to less than 0.06 µS/cm. In this model one H6 column should be replaced. It should be remembered that the volume of purified water depends on the quality of the feed water, the maximum amount of salts dissolved in the feed water – 1200 mg / l. After 5000 dm3, the H6 module should be replaced.
Cat. no.: EJ-5000-1
The H6TOC ion exchange module is a mixture of ion exchange beds – strongly acid cation exchanger and strongly basic anion exchanger. Removes mineral salts remaining in water after reverse osmosis to less than 0.06 µS/cm. In this model one H6TOC column should be replaced. It should be remembered that the volume of purified water depends on the quality of the feed water, the maximum amount of salts dissolved in the feed water – 1200 mg / l. After 5000 dm3 the H6TOC module should be replaced..
p>Cat. no.: EJ-2000-0
The H7 ion exchange module is a mixture of ion exchange beds – strongly acid cation exchanger and strongly basic anion exchanger. Removes mineral salts remaining in water after reverse osmosis to less than 0.06 µS / cm. In this model, the 2xH7 set should be replaced. In demineralizers manufactured until the end of April 2013, it appears as a “cleaning filter”.
Cat. no: EJ-2000-1
The H7TOC ion exchange module is a mixture of ion exchange beds – strongly acid cation exchanger and strongly basic anion exchanger. Removes mineral salts remaining in water after reverse osmosis to less than 0.06 µS/cm. Available in the HL5 UV, HLP10 UV and HLP30 UV models. The 2x H7TOC set should be replaced on these models.
In demineralizers manufactured until the end of April 2013, it appears as the “H3TOC module”
Cat. no.: EM-SP-20
Ready-to-use flow filter designed to remove bacteria and colloidal suspensions from purified water. It is part of the HLP 5s, HLP 5sp, HLP 5uv, HLP 10s, HLP 10sp, HLP 10uv, HLP 20s, HLP 20sp, HLP 20uv, HLP 30s, HLP 30sp, HLP 30uv, or is a purchase option.
Cat. no: EUV-254-HLP – from April 2013 r.
Cat. no: EUV-254-0 – until April 2013 r.
The radiator emits radiation at a wavelength of 254 nm, which causes a photochemical reaction that damages the DNA structures of microorganisms in the water. This type of radiator is used in models HLP 5uv, HLP 10uv, HLP 20uv, HLP 30uv. Its proper operation is up to 8,500 hours. Warning! In models until April 2013, we used the EUV-254-0 radiator type.
SPRING models from the demineralizer family equipped with various modules and filters.List of all elements together with catalog numbers included below in the tabs.
The table with individual components of content is in PDF.
Cat. no.: EO-005-10
The sediment prefilter prepares tap water for the purification process in the Technical Plus demineralizers. They are made of polypropylene fiber wound on a filter core, thus creating a gradient filter. They retain mechanical impurities with a particle size of 1µm to 20µm (depending on the porosity of the filter). The life of the cartridges is 3-6 months (it may change depending on the flow and the level and type of water pollution).
Cat. no: EW-001-L
The carbon filter prepares tap water for the further purification process in demineralisers manufactured until the end of April 2013. The filter is filled with granular activated carbon located in the filter housing (¼ ”NPT connection). Impurities (mainly chlorine and chlorinated substances dissolved in tap water) undergo sorption on activated carbon. The lifetime of the module is 3-6 months (it may change depending on the flow and the level and type of water pollution).
Cat no.: EO-MA-12
The sediment-carbon-softening module prepares tap water for the reverse osmosis process in the HLP, Technical, Technical Plus, Spring and R series demineralizers. Removes mechanical particles (sand, rust, mud), chlorine, chlorinated substances dissolved in water and calcium and magnesium ions responsible for water hardness. The module’s service life is 3-6 months (it may change depending on the flow and the level and type of water pollution).
Nr katalogowy: EJ-5000-0
The H6 ion exchange module is a mixture of ion exchange beds – strongly acid cation exchanger and strongly basic anion exchanger. Removes mineral salts remaining in water after reverse osmosis to less than 0.06 µS / cm. In this model one H6 column should be replaced. It should be remembered that the volume of purified water depends on the quality of the feed water, the maximum amount of salts dissolved in the feed water – 1200 mg/l. After 5000 dm3, the H6 module should be replaced. The H6 module is available in the following models: SPRING 10, 10s, 20, 20s, 30,30s, 40 and 60.
Nr katalogowy: EJ-5000-1
Moduł jonowymienny H6TOC jest mieszaniną złóż jonowymiennych – kationitu silnie kwaśnego i anionitu silnie zasadowego. Usuwa sole mineralne pozostałe w wodzie po procesie odwróconej osmozy do poziomu poniżej 0,06 µS/cm. Należy pamietać, że objętość wody oczyszczonej zależy od jakości wody zasilającej, maksymalna ilość soli rozpuszczonych w wodzie zasilającej – 1200 mg/l. Po 5000 dm3 moduł H6TOC należy wymienić na nowy. Modul H6TOC zastosowany jest w modelach SPRING 10uv,20uv,30uv, 40uv, 60uv.
Cat no.: EJ-2000-0
The H7 ion exchange module is a mixture of ion exchange beds – strongly acid cation exchanger and strongly basic anion exchanger. Removes mineral salts remaining in water after reverse osmosis to less than 0.06 µS / cm. In the SPRING 5, SPRING 5s model the 2xH7 set should be replaced.
Cat. no.: EJ-2000-1
The H7TOC ion exchange module is a mixture of ion exchange beds – strongly acid cation exchanger and strongly basic anion exchanger. Removes mineral salts remaining in water after reverse osmosis to less than 0.06 µS/cm. Occurs in the SPRING 5UV model. In this model, the 2x H7TOC set should be replaced.
Cat no: EM-SP-20
Ready-to-use flow filters designed to remove bacteria and colloidal suspensions from purified water. It is part of the SPRING 5uv, 10uv 20uv, 30uv, 40uv, 50uv model or is a purchase option.
Cat. no: EUV-254-HLP
The radiator emits radiation at a wavelength of 254 nm, which causes a photochemical reaction that damages the DNA structures of microorganisms in the water. This type of heater is used in models SPRING 5uv, 10uv, 20uv, 30uv, 40uv, 60uv. Its proper operation is up to 8,500 hours.
ULTRA models from the demineralizer family equipped with various modules and filters.List of all elements together with catalog numbers included below in the tabs.
The table with individual components of content is in PDF.
Cat. no EJ-2000-1
The H7TOC ion exchange module is a mixture of ion exchange beds – strongly acid cation exchanger and strongly basic anion exchanger. Removes mineral salts remaining in water after reverse osmosis to less than 0.06 µS/cm. Available on all ULTRA models.
Cat. no.: EM-SP-20
Ready-to-use flow filters designed to remove bacteria and colloidal suspensions from purified water. It is part of the model of all ULTRA series models.
Cat. no.: EUV-254-HLP
The radiator emits radiation at a wavelength of 254 nm, which causes a photochemical reaction that damages the DNA structures of microorganisms in the water. We use this type of heater in the ULTRA model. Its proper operation is up to 8,500 hours of lighting.
Cat. no.: EUV-185-254-HLP
The radiator emits radiation with a wavelength of 185-254 nm, which causes a photochemical reaction damaging the DNA structures of microorganisms in the water. This type of radiator is used in ULTRA uv and ULTRA uf models. Its proper operation is up to 8,500 hours of lighting.
Cat. no.: EU-HLP-01
In the ultrafiltration process, endotoxins (toxins resulting from the breakdown of bacterial cells) as well as RNase and DNase (enzymes involved in the hydrolysis of RNA and DNA chains) are removed. Ultrafiltration modules or capsules are used for this purpose.
R models from the demineralizer family equipped with various modules and filters.List of all elements together with catalog numbers included below in the tabs.
The table with individual components of content is in PDF.
Cat no.: EO-005-10
The sediment insert prepares tap water for the purification process in the R series demineralizers. They are made of polypropylene fiber wound on a filter core, thus creating a gradient filter. They retain mechanical impurities with a particle size of 1µm to 20µm (depending on the porosity of the filter). The life of the cartridges is 3-6 months (it may change depending on the flow and the level and type of water pollution).
Cat. no: EW-001-10
Coal cartridges prepare tap water for further purification by removing chlorine and chlorine derivatives dissolved in tap water. Impurities are sorbed on activated carbon. The module’s service life is 3-6 months (it may change depending on the flow and the level and type of water pollution).
Cat no.: EO-MA-12
The sediment-carbon-softening module prepares tap water for the reverse osmosis process in the HLP, Technical, Technical Plus, Spring and R series demineralizers. Removes mechanical particles (sand, rust, mud), chlorine, chlorinated substances dissolved in water and calcium and magnesium ions responsible for water hardness. The module’s service life is 3-6 months (it may change depending on the flow and the level and type of water pollution).
Cat. no.: EJ-5000-1
The H6TOC ion exchange module is a mixture of ion exchange beds – strongly acid cation exchanger and strongly basic anion exchanger. Removes mineral salts remaining in water after reverse osmosis to less than 0.06 µS/cm. It should be remembered that the volume of purified water depends on the quality of the feed water, the maximum amount of salts dissolved in the feed water – 1200 mg / l. After 5000 dm3 the H6TOC module should be replaced.
Cat. no EJ-2000-1
The H7TOC ion exchange module is a mixture of ion exchange beds – strongly acid cation exchanger and strongly basic anion exchanger. Removes mineral salts remaining in water after reverse osmosis to less than 0.06 µS/cm. Available on all ULTRA models.
Cat. no.: EM-SP-20
<
Ready-to-use flow filters designed to remove bacteria and colloidal suspensions from purified water.
Cat. no.: EUV-254-HLP
The radiator emits radiation at a wavelength of 254 nm, which causes a photochemical reaction that damages the DNA structures of microorganisms in the water. This type of radiator is used in models HLP 5uv, HLP 10uv, HLP 20uv, HLP 30uv. Its proper operation is up to 8,500 hours. Warning! In models until April 2013, we used the EUV-254-0 radiator type.
Cat. no.: EUV-185-254-HLP
The radiator emits radiation with a wavelength of 185 and 254 nm, which causes a photochemical reaction damaging the DNA structures of microorganisms in the water. We use this type of heater in the R5UV, R5UF, R10UV, R10UV, R20UV, R20UV, R30UV, R30UV models. Its proper operation is up to 8,500 hours of lighting.
Cat. no.: EU-HLP-01
In the ultrafiltration process, endotoxins (toxins resulting from the breakdown of bacterial cells) as well as RNase and DNase (enzymes involved in the hydrolysis of RNA and DNA chains) are removed. Ultrafiltration modules or capsules are used for this purpose. We filter the ultrafiltration module in the R5UF, R10UF, R20UF and R30UF modules.
BASIC models from the demineralizer family equipped with various modules and filters.List of all elements together with catalog numbers included below in the tabs.
The table with individual components of content is in PDF.
Cat. no.: EO-005-10
The sediment prefilter prepares tap water for the purification process in the Technical Plus demineralizers. They are made of polypropylene fiber wound on a filter core, thus creating a gradient filter. They retain mechanical impurities with a particle size of 1µm to 20µm (depending on the porosity of the filter). The life of the cartridges is 3-6 months (it may change depending on the flow and the level and type of water pollution).
Cat. no.: EW-001-10
Coal cartridges prepare tap water for further purification by removing chlorine and chlorine derivatives dissolved in tap water. Impurities are sorbed on activated carbon. The module’s service life is 3-6 months (it may change depending on the flow and the level and type of water pollution).
Cat. no.: EO-MA-12
The sediment-carbon-softening module prepares tap water for the reverse osmosis process in the HLP, Technical, Technical Plus, Spring and R series demineralizers. Removes mechanical particles (sand, rust, mud), chlorine, chlorinated substances dissolved in water and calcium and magnesium ions responsible for water hardness. The module’s service life is 3-6 months (it may change depending on the flow and the level and type of water pollution).
Cat. no: EJ-5000-0
The H6 ion exchange module is a mixture of ion exchange beds – strongly acid cation exchanger and strongly basic anion exchanger. Removes mineral salts remaining in water after reverse osmosis to less than 0.06 µS/cm. In this model one H6 column should be replaced. It should be remembered that the volume of purified water depends on the quality of the feed water, the maximum amount of salts dissolved in the feed water – 1200 mg / l. After 5000 dm3, the H6 module should be replaced.
Cat. no.: EJ-5000-0
Mechanical contribution
Sludge cartridges prepare tap water for the purification process in the HLP, Technical, Technical Plus, Spring and R series demineralizers. They are made of polypropylene fiber wound on a filter core, thus creating a gradient filter. They retain mechanical impurities with a particle size of 1µm to 20µm (depending on the porosity of the filter). The life of the cartridges is 3-6 months (it may change depending on the flow and the level and type of water pollution).
1μm 10" / EO-001-10
1μm 20" / EO-001-20
5μm 10" / EO-005-10
5μm 20" / EO-005-20
10μm 10" / EO-010-10
10μm 20" / EO-010-20
20μm 10" / EO-020-10
20μm 20" / EO-020-20
Module A2
The sediment-carbon-softening module prepares tap water for the reverse osmosis process in the HLP, Technical, Technical Plus, Spring and R series demineralizers. Removes mechanical particles (sand, rust, mud), chlorine, chlorinated substances dissolved in water and calcium and magnesium ions responsible for water hardness. The module lifetime is 3-6 months (it may change depending on the flow and the level and type of water pollution).
A2 module / EO-MA-12
Carbon cartridge GAC
Coal cartridges prepare tap water for further purification by removing chlorine and chlorine derivatives dissolved in tap water. Impurities are sorbed on activated carbon. The module lifetime is 3-6 months (it may change depending on the flow and the level and type of water pollution).
GAC 10" cartridge / EW-001-10
GAC 20" cartridge / EW-001-20
Microfiltration capsule
Ready-to-use flow filters for removing bacteria and colloidal suspensions from purified water. They are made of a polypropylene housing with a double-layer polytetrafluoroethylene (PTFE) membrane. Working capacity: the number of pores in the membrane is equal to the number of bacteria retained on a given membrane surface. 1 x 107 CFU/cm2.
0,45/0,2μm 150 cm2 1/4" / EM-SP-20-14
0,45/0,2μm 150 cm2 CE / EM-SP-20
Reverse osmosis module
RO modules prepare tap water for the demineralization process on a mixed ion exchange bed. They are made of many layers of semi-permeable membranes wound on a perforated mandrel. The degree of retention of the reverse osmosis process is variable, it is 96-99%. It depends on salinity, pressure, temperature and flow rate of tap water.
RO 4040 cartridge / ER-WRO-4040
RO 4040 module / ER-RO-4040
RO D100 module / ER-RO-100
RO D400 module / ER-RO-400
Softening cartridge
The softening cartridge removes calcium and magnesium ions that are responsible for the hardness of the water. It is filled with strongly acidic resin. The insert is compatible with a 10″ or 20″ housing.
10" softening cartridge / EZ-001-10
Iron removal cartridge
The iron removal cartridge removes iron and manganese ions, hydrogen sulfide as well as the metallic taste and smell of tap water. It is filled with a mixture of high-performance ion exchange beds. It is compatible with 10″ or 20″ housing.
softening cartridge 10" / EF-001-10
softening cartridge 20" / EF-001-20
Filter housing 1/4 EG 10″
10″ polypropylene housing with single sealing O-ring in the body. It is designed for all 10” units with a diameter of 2.5” (pre-filter, carbon filter, softening filter, de-ironing filter, etc.). It is equipped with a fixing handle.
Technical data:
Connection – 1/4 “internal thread.
Maximum working temperature: 37.7 ° C.
Maximum working pressure: 6.9 bar.
Designed for cold water filtration.
Shade material – high-quality polypropylene.
Head material – polypropylene.
White color.
Possibility of series and parallel connection of bodies.
Dimensions:
Height without a fixing handle: 29 cm.
Diameter: 11 cm.
Filter housing ½ EG and ¾ EG 10″
10” polypropylene housing with double sealing O-ring on the body. It is designed for all 10” filters with a diameter of 2.5″ (sediment, sludge-carbon, carbon, softening, de-ironing, etc.). The body head is equipped with a breather for easy exchange of cartridges and a fixing handle.
Technical data:
Connection – brass internal thread 1/2 “
Maximum working temperature: 30 ° C.
Maximum working pressure: 8.0 bar.
Designed for cold water filtration.
Shade material – high-quality polypropylene.
Head material – polypropylene.
Color: colorless body, blue head.
Possibility of series and parallel connection of bodies.
Dimensions:
Height without a fixing handle: 32 cm.
Diameter: 12.3 cm.
Technical data:
Connection – brass internal thread ¾”.
Maximum working temperature: 30 ° C.
Maximum working pressure: 8.0 bar.
Designed for cold water filtration.
Shade material – high-quality polypropylene.
Head material – polypropylene.
Color: colorless body, blue head.
Possibility of series and parallel connection of bodies.
Dimensions:
Height without a fixing handle: 32 cm.
Diameter: 12.3 cm.
Filter housing 20″
20” polypropylene housing with single sealing O-ring in the body. It is designed for all 20” filters with a diameter of 2.5″ (sediment, carbon, softening, de-ironing, etc.). The body head is equipped with a breather for easy exchange of cartridges and a fixing handle.
Technical data:
Connection – ½
Maximum working temperature: 52°C.
Maximum working pressure: 8.6 bar.
Designed for cold water filtration.
Shade material – high-quality polypropylene.
Head material – polypropylene reinforced with nylon.
Color: blue body, black head.
Possibility of series and parallel connection of bodies.
Dimensions:
Height without a fixing handle: 59 cm.
Diameter: 18.0 cm.
Technical data:
Connection – 3/4″
Maximum working temperature: 52°C.
Maximum working pressure: 8.6 bar.
Designed for cold water filtration.
Shade material – high-quality polypropylene.
Head material – polypropylene reinforced with nylon.
Color: blue body, black head.
Possibility of series and parallel connection of bodies.
Dimensions:
Height without a fixing handle: 59 cm.
Diameter: 18.0 cm.
Technical data:
Connection – 3/8″
Maximum working temperature: 52°C.
Maximum working pressure: 8.6 bar.
Designed for cold water filtration.
Shade material – high-quality polypropylene.
Head material – polypropylene reinforced with nylon.
Color: blue body, black head.
Possibility of series and parallel connection of bodies.
Dimensions:
Height without a fixing handle: 59 cm.
Diameter: 18.0 cm.
Sediment-carbon module 10″
Sludge-carbon cartridge designed for 10″ housing – removes both mechanical particles (sand, rust, silt) as well as chlorine and chlorinated substances, preparing water for subsequent stages of purification.
5μm/GAC10" / EOW-011-10
Ultrafiltration module
In the ultrafiltration process, endotoxins (toxins resulting from the breakdown of bacterial cells) as well as RNase and DNase (enzymes involved in the hydrolysis of RNA and DNA chains) are removed. Ultrafiltration modules or capsules are used for this.
UF J module / EU-TJ-01
UF HLP module / EU-HLP-01
UF capsule / EU-HLP-02
UV lamp radiator
Radiators emit radiation with a wavelength of 254 nm or / and 185 nm, which causes a photochemical reaction damaging the DNA structures of microorganisms in the water or/and lowering the TOC level in the process of photooxidation.
254nm 463RL / EUV-254-463RL
185nm HLP / EUV-185-HLP
185/254nm HLP / EUV-185-254-HLP
185/254nm ST / EUV-185-254-0
254nm HLP / EUV-254-HLP
254nm ST / EUV-254-0
Ion exchange modules
The ion exchange module is a mixture of ion exchange beds – strongly acid cation exchanger and strongly basic anion exchanger. Removes mineral salts remaining in water after reverse osmosis to less than 0.06 µS / cm.
H7 / EJ-2000-0
The H7 ion exchange filter is a mixture of ion-exchange beds – strongly acid cation exchanger and strongly basic anion exchanger (2000 ml bed). Removes mineral salts remaining in water after reverse osmosis to less than 0.06 µS / cm. The working capacity of the H7 filter is 56g CaCO3.
H7TOC / EJ-2000-1
The H7TOC ion exchange filter is a mixture of ion-exchange beds – strongly acid cation exchanger and strongly basic anion exchanger (2000 ml bed). Removes mineral salts remaining in water after reverse osmosis to less than 0.06 µS / cm. The working capacity of the H7TOC filter is 56g CaCO3.
H5 / EJ-0250-0
The H5 ion exchange filter is a mixture of ion-exchange beds – strongly acid cation exchanger and strongly basic anion exchanger (250 ml bed). Removes mineral salts remaining in water after reverse osmosis to less than 0.06 µS / cm. The working capacity of the H5 filter is 7g CaCO3.
It occurs in demineralizers manufactured until the end of April 2013 as a cleaning filter.
H6 / EJ-5000-0
The H6 ion exchange filter is a mixture of ion-exchange beds – strongly acid cation exchanger and strongly basic anion exchanger (5000 ml bed). Removes mineral salts remaining in water after reverse osmosis to less than 0.06 µS / cm. The working capacity of the H6 filter is 140g CaCO3.
H6TOC / EJ-5000-1
The H6TOC ion exchange filter is a mixture of ion-exchange beds – strongly acid cation exchanger and strongly basic anion exchanger (5000 ml bed). Removes mineral salts remaining in water after reverse osmosis to less than 0.06 µS / cm. The working capacity of the H6TOC filter is 140g CaCO3.
H3 / EJ-0500-0
The H3 ion exchange filter is a mixture of ion-exchange beds – strongly acid cation exchanger and strongly basic anion exchanger (500 ml bed). Removes mineral salts remaining in water after reverse osmosis to less than 0.06 µS / cm. The working capacity of the H3 filter is 14g CaCO3.
It occurs in demineralizers manufactured until the end of April 2013 as a cleaning filter.
H3TOC / EJ-0500-1
The H3TOC ion exchange filter is a mixture of ion-exchange beds – strongly acid cation exchanger and strongly basic anion exchanger (500 ml bed TOC). Removes mineral salts remaining in water after reverse osmosis to less than 0.06 µS / cm. The working capacity of the H3TOC filter is 14g CaCO3.
It occurs in demineralizers manufactured until the end of April 2013 as a cleaning filter.
Sediment filter H1
The mechanical filter prepares tap water for further purification in demineralisers manufactured until the end of April 2013. It is made of a 1 µm polypropylene cartridge placed in the filter housing (1/4 “NPT connection). The module lifetime is 3-6 months (it may change depending on the flow and the level and type of water pollution).
H1 filter / EO-001-L
Carbon filter GAC H2
The carbon filter prepares tap water for the further purification process in demineralisers manufactured until the end of April 2013. The filter is filled with granular activated carbon located in the filter housing (¼ ”NPT connection). Impurities (mainly chlorine and chlorinated substances dissolved in tap water) undergo sorption on activated carbon. The lifetime of the module is 3-6 months (it may change depending on the flow and the level and type of water pollution).
GAC H2 filter / EW-001-L
Tableted salt
High-quality tableted (tableted) salt intended for regeneration of softening deposits in automatic water softeners, e.g. HLP Plus. It is the most important product for trouble-free operation of softening stations. Salt consumption depends on the amount of water used and its hardness. Correct use of the softener and refiling it up with salt also helps to reduce the operating costs of water treatment station and other laboratory equipment.
Packaging: 25 kg
Tableted salt 25kg / ES-001-0
Ion exchange resin – bi-ionite
Ready to use mixture of ion exchange deposits, intended for the production of demineralized water with high chemical purity. This resin is obtained by thoroughly mixing two fully regenerated gel ion resins – strongly acid cation exchanger and type 1 strongly basic anion exchanger. Their percentage share includes the statistical chemical composition of water subjected to demineralization. The ion exchange resin (bi-ionite) contains completely demineralized water, free of silica. It can be used for demineralization of raw water or as the last step of cleaning the water purified by reverse osmosis, electrodialysis or distillation.
Ion exchange resin (1 liter) / EJ-001-0
Ion exchange resin TOC (1 liter) / EJ-001-1